This project was built and designed by Tim from Casual Builds. It’s a beginner-friendly guide to making classic frame and panel cabinet doors using a table saw, ideal for upgrading furniture or learning foundational joinery techniques.
With clean lines and timeless appeal, frame and panel doors are a staple in both modern and traditional cabinetry. Tim walks through each step clearly, making this a great starting point for those new to cabinet building or anyone refining their shop skills.
Watch the full video and subscribe to Tim’s channel:
What Are Frame and Panel Doors?
A frame and panel door is made up of four outer frame pieces—two vertical stiles and two horizontal rails—that surround a thinner center panel. The frame is joined with grooves and tenons, allowing the panel to “float” inside.
This design provides strength and stability while giving the wood room to expand and contract with seasonal changes. It’s a reliable construction method that holds up well over time and adds a polished look to any cabinet.
Start with Accurate Measurements
Tim begins by measuring the cabinet opening where the doors will be installed. Accurate dimensions are essential, especially when planning for overlay hinges, which add to the door’s width and height.
He recommends adding about three-quarters of an inch overall to accommodate the overlay. This ensures the doors will cover the cabinet frame properly once installed.
Cutting the Stiles and Rails
After the measurements are finalized, Tim rips the rails and stiles to a consistent width using a table saw. Uniform sizing helps with assembly later and gives the door a balanced appearance.
Once the pieces are ripped, they’re cut to length. The vertical stiles stay full height, while the horizontal rails are cut shorter to account for the tenons that will be added on each end.
Making the Grooves
Grooves are cut into the inside edges of all four frame pieces. These grooves will hold the center panel and must be sized to match the panel’s thickness.
Tim uses a standard table saw blade, setting the height to about half an inch and adjusting the fence so the groove lands in the center of each board. He tests on scrap wood first to dial in the fit, making sure the panel will slide in easily without being too loose.
Cutting Tenons on the Rails
Next, the ends of the horizontal rails are shaped into tenons. These are designed to fit into the grooves cut into the stiles, locking the frame together.
The tenons are made using multiple passes over the table saw blade. Tim takes his time here to ensure that the shoulders are clean and that each tenon fits snugly into its corresponding groove.
Prepping the Center Panel
For the panel, Tim uses a quarter-inch plywood sheet, which is a common and stable choice for this type of door. The panel is cut slightly smaller than the space inside the grooves, leaving a small gap on all sides to allow for seasonal expansion.
Failing to leave this space can cause the panel to bow or crack over time, especially in environments with fluctuating humidity. A well-fitted panel will sit loosely inside the frame and be held securely without glue.
Assembly and Clamping
Once all components are cut, it’s time to assemble the door. Tim applies glue only to the tenon-and-groove joints of the frame—never to the panel itself—allowing it to move freely inside.
After inserting the tenons into the grooves, the frame is clamped and checked for square. Clamping pressure is applied evenly to avoid shifting and to ensure a clean, flat glue-up.
Sanding and Finishing the Door
Once the glue is dry, the clamps are removed and the door is lightly sanded to remove any surface imperfections. Tim rounds over or chamfers the outer edges to soften the look and make the door feel more finished.
At this stage, the door is ready for your choice of finish. Paint, stain, or clear coat all work well depending on the style of your project. Tim emphasizes sanding between coats and applying a durable topcoat for long-lasting results.
A Project That Teaches Core Skills
Building frame and panel cabinet doors teaches essential woodworking techniques: accurate measuring, consistent cutting, joinery, and clean assembly. It’s a satisfying project that’s simple in structure but foundational in skill.
Whether you’re updating kitchen cabinets, making a new piece of furniture, or just practicing shop techniques, this project is a great one to try. Tim’s straightforward process helps eliminate confusion and gives you the confidence to tackle more complex projects down the road.
Please support Tim by visiting his website: https://www.casualbuilds.com/.