Turning a Messy Table Into a Thick Wood Masterpiece

Photo of author

This project was built and designed by Chris from A Glimpse Inside.

Chris set out to solve a problem that plagues a lot of households with young kids: a table that always looks dirty no matter how often it gets wiped down. His plan was to build a wood topper that would sit over the existing table, giving the illusion of a thick, solid slab while actually covering up the raised-edge surface underneath that seemed to attract every bit of mess imaginable.

Watch the full video and subscribe to A Glimpse Inside:

Starting With Exterior-Grade Plywood

Chris began with a sheet of exterior-rated plywood that is marketed to last for years outside without finishing or delaminating. Despite the claims, he found the material already showing some wear before he even got started, which set the tone for a build full of small surprises.

Rather than get frustrated by the imperfections, he decided early on to let some of them stay. He mentioned leaving certain router bit setups unchanged on purpose, knowing it would create slightly rougher cuts along some edges instead of perfectly clean ones.

Extending the Surface With CNC-Cut Pieces

Since the plywood sheet was narrower than the actual table it needed to cover, Chris had to find a way to extend the surface just enough to wrap around the table’s edge. His solution was to cut a series of boomerang-shaped pieces on the CNC machine and use them as an extended frame around the perimeter.

By gluing and pinning two layers of these shapes around the edges, he gained the extra width needed for the topper to drape over the table properly. The same boomerang pieces were also added to the underside, giving the illusion of a much thicker slab while keeping the interior mostly hollow to save on material and weight.

Packing tape was applied along the underside seams as a precaution against resin leaking through any gaps, paired with paper laid down on the work surface for extra protection. The whole assembly was then raised slightly off the table using sacrificial leveling nuts, making it easier to work around and pour into.

Mixing and Pouring the Resin

With the boomerang pieces in place, Chris mixed resin tinted with a black pigment to fill the gaps between pieces. The resin had aged a bit in storage and taken on an amber tint, but he explained that color shift in epoxy over time does not affect its curing, strength, or workability, only its appearance.

Pouring the mixture from a condiment-style squeeze bottle made the process far more controlled than trying to pour straight from a mixing cup. The technique allowed him to fill the many small cavities between the boomerang shapes without the mess he was expecting.

Flattening the Surface

Once the resin cured, the next challenge was flattening everything out using a CNC router equipped with a planing bit. Since the piece was plywood rather than a solid slab, the usual spoilboard clamps would not grip it properly, so Chris experimented with screws in the corners and eventually added several more fasteners around the perimeter to keep everything secure during the cut.

The flattening pass removed more material than intended in a few spots, including some of the black resin inlay that had just been poured. While frustrating in the moment, Chris pushed forward, treating it as part of the learning process rather than a reason to start over.

Embracing the Imperfections

Throughout the build, Chris kept circling back to the idea that imperfections are not something to fear. Burn marks on the plywood, a few surface gaps, and uneven resin coverage all became part of the character of the piece rather than problems to hide.

For the remaining gaps, he filled them with a UV-cure resin that hardens in about a minute under a built-in light. It is a handy option for quick repairs when there is no time to wait on standard resin to cure overnight.

WANT TO SAVE THIS PROJECT?

Enter your email below & we'll send it straight to your inbox.

Applying the Topcoat

For the finish, Chris used a clear water-based tabletop coating applied in several thin layers, sanding lightly between coats to knock down any texture. After building up those layers, he sanded the entire surface smooth before moving on to a much thicker flood coat of the same finish.

Spreading that thick final layer required a custom-notched spreader tool to control how much material went down at once. Even though it looked uneven right after application, the self-leveling nature of the finish meant it settled out smooth and glass-like by the next day.

A final pass with a fine finishing pad took down some of the gloss and smoothed out any remaining texture, giving the surface a soft, matte feel rather than a high-shine look.

Mounting the Topper

Instead of permanently bonding the new surface to the table, Chris opted for a few beads of silicone at several points around the perimeter. This approach holds the topper securely in place while still allowing it to be removed if needed down the road.

A Project Full of Lessons

Looking back at the build, Chris pointed out how even after years of running a CNC machine, there is always more to learn, especially when pushing a project outside the usual routine. The combination of resin work, CNC flattening, and a thick multi-layer finish made this one of his more technically involved builds, even though the end goal was a simple table topper.

The finished piece ended up with a few visible quirks, including a section where the black resin inlay was accidentally removed during flattening. Rather than viewing it as a flaw, Chris saw it as something that gives the piece its own story and makes it a natural conversation starter for anyone who sees it.

Watch the full video and subscribe to A Glimpse Inside:

Matt Hagens

Matt’s Take

These are my personal thoughts and tips based on my own experience in the shop. This section is not written, reviewed, or endorsed by the original creator of this project.

Matt’s Take: This build is a great example of how a “topper” project can turn into a full-blown engineering challenge once resin and CNC work get involved. Building up thickness with hollow sections instead of a solid slab is a smart move for weight and material cost, but it’s worth remembering that any hollow assembly needs a solid, flat reference surface before you start flattening or routing. Even small amounts of flex can throw off your cut depth in ways that are hard to predict.

On the resin side, that amber shift Chris mentioned is really common with epoxy that’s been sitting around. UV exposure and just time in general will yellow resin, but it’s purely cosmetic in most cases — as long as it’s mixed properly and fully cured, the strength is still there. If you’re working with pigmented resin in small cavities, a squeeze bottle is honestly one of the most underrated tools in the shop. It gives you way more control than pouring from a cup and cuts down on drips and waste.

Flattening plywood assemblies on a CNC without traditional spoilboard clamps is tricky, and screws in strategic spots are a reasonable workaround as long as you’re mindful of where your bit will travel so you’re not clipping fasteners. If you’re doing this at home without a CNC, a router sled is a solid alternative for flattening wide panels.

Lastly, using silicone instead of permanent adhesive to mount the topper is a nice touch — it keeps things removable for cleaning or future repairs, which matters a lot on a piece that’s meant to protect a table long-term.

**Please support the YouTube video creators by subscribing to their channels. If you make a purchase through one of our links, we might get a commission.**

WANT TO SAVE THIS PROJECT?

Enter your email below & we'll send it straight to your inbox.

Please leave a comment to join the discussion