Building Custom Screen Doors for a Deck

Photo of author

This project was built and designed by Jason from PatriotDIY.

After finishing up a deck cleaning, staining, and screening project, Jason took on the final piece of the puzzle: building a set of custom screen doors to complete the enclosed porch area. The build covers everything from lumber selection and joinery to screen installation and weatherproofing, making it a great reference for anyone looking to add a screen door to their own outdoor space.

Watch the full video and subscribe to PatriotDIY:

Lumber Selection and Prep

Jason starts by walking through a few different ways to source material for the door frame. Standard treated dimensional lumber from a home center works fine, as long as you take the time to pick through the stack for the straightest boards with the fewest knots.

For those who want cleaner stock, he suggests buying wider boards and ripping them down on a table saw to cut around defects. He also shows his own preferred method, running rough lumber through a planer and jointer to create smooth, perfectly square stock before cutting any joinery.

This section is a good reminder that quality control at the lumber stage pays off later, since straighter stock makes for doors that hang and close properly.

Layout and Joinery

After measuring the doorway, Jason cuts all the frame components to length, including a wider board at the bottom of the door for a more finished look. He lays everything out on the workbench to confirm the layout before cutting any joints.

For joining the frame pieces, he highlights several approachable options including dowels and pocket hole screws with plugs, both of which can be painted over without leaving visible seams. For his own build, he opts for loose tenon joinery using a dedicated mortising tool, which allows him to quickly cut accurate mortises at each joint.

He intentionally cuts the mortises slightly oversized to allow a bit of wiggle room when aligning the frame during glue-up, a small trick that makes assembly much less stressful.

Assembly and Shaping

Glue-up involves coating both the mortises and tenons generously with exterior wood glue, then assembling the frame piece by piece while wiping away squeeze-out as he goes. Corner clamps help keep the door square while everything cures.

Once the glue sets, Jason sands the frame smooth and routs a ledge along one inside edge to create a mounting surface for the screen material later. Because the router leaves rounded corners, he goes back with a chisel to square them up by hand.

A round-over bit on the outer edges knocks off any sharp corners, giving the door a more finished, comfortable feel before moving into paint and screen installation.

Finishing and Screen Installation

With shaping complete, Jason applies a coat of exterior paint to protect the wood and give the door a clean appearance. Once dry, he stretches the screen material across the opening and staples it into the routed ledge.

Maintaining even tension across the screen is important here, pulling it tight enough to avoid sagging without overstretching or tearing the material. Staples are spaced closely together for durability, and any excess screen is trimmed away with a razor knife.

To hide the staples and give the door a more polished look, Jason adds thin trim strips over the stapled edges, pre-painting them before attaching with brad nails and filling the nail holes with caulk afterward.

WANT TO SAVE THIS PROJECT?

Enter your email below & we'll send it straight to your inbox.

Hardware and Installation

Since this is a double door setup, one side remains stationary while the other operates as the main entry point. Jason covers a couple of options for securing the stationary door, from a simple surface-mounted pin to a more refined inset flush bolt that requires routing a mortise into the door’s edge.

Hinges are measured, marked, and pre-installed before the doors are set into the frame using a spacer to maintain proper clearance at the floor. After confirming each door swings freely, Jason moves on to weatherproofing.

Three types of weather stripping handle different gaps around the doors: a foam-backed stop strip around the perimeter, a custom-built astragal piece to seal the gap between the two doors, and a brush sweep at the bottom to block out insects while still allowing smooth movement across the deck surface.

Bringing It All Together

With the hardware installed and weatherstripping in place, the screen doors complete the enclosed porch project from start to finish. Jason’s approach throughout the video emphasizes flexibility, offering multiple methods for joinery, lumber prep, and hardware so builders of different skill levels and tool collections can adapt the project to their own shop.

This build is a solid example of how a functional, good-looking screen door can be made from basic construction lumber with the right joinery and finishing techniques, making it an approachable project for anyone looking to upgrade their outdoor living space.

Watch the full video and subscribe to PatriotDIY:

Matt Hagens

Matt’s Take

These are my personal thoughts and tips based on my own experience in the shop. This section is not written, reviewed, or endorsed by the original creator of this project.

Matt’s Take: Screen doors look simple until you actually build one, and this video does a nice job showing why lumber selection matters so much here. Treated dimensional lumber moves a lot as it dries, so if you go that route, let your boards acclimate in the space they’ll be used before you cut any joinery. A door frame that’s dead flat on build day can twist a week later if the wood wasn’t given time to settle, and that’s a frustrating way to find out your door no longer closes square.

On the joinery side, loose tenons with a dedicated mortiser are great if you have one, but don’t feel like you need that tool to get a strong door. Pocket screws with exterior-rated glue at the joints hold up fine for this kind of application, especially on a door that’s not bearing much weight. Just make sure whatever glue you use is rated for exterior or at least high-moisture exposure, since a screen door lives in a tough environment with constant temperature and humidity swings.

When it comes to screen tension, a cheap screen-rolling tool from the hardware store makes a noticeable difference over just pulling by hand. It helps keep even pressure across the whole span so you don’t end up with wavy spots. And one safety note worth repeating anytime staples or brad nailers are involved: keep your off-hand well clear of the firing path, especially when working close to an edge like that routed screen ledge.

Overall this is a great beginner-friendly project because it doesn’t demand a fully loaded shop to get a professional result.

**Please support the YouTube video creators by subscribing to their channels. If you make a purchase through one of our links, we might get a commission.**

WANT TO SAVE THIS PROJECT?

Enter your email below & we'll send it straight to your inbox.

Please leave a comment to join the discussion