This woodworking technique was demonstrated and explained by Jodee from Inspire Woodcraft. It’s a clever way to glue wood without using clamps—perfect for delicate pieces, tight spaces, or when you simply run out of clamps in the shop.
By rubbing two pieces of glued wood together, the method builds enough tack to hold a strong bond as the glue cures naturally. While it won’t replace clamps in every scenario, it’s a valuable addition to your joinery skillset.
Watch the full video and subscribe to Jodee’s channel:
What Is a Rub Joint?
The rub joint relies on friction, suction, and tack rather than clamping force. You apply a thin layer of glue to two flat, smooth surfaces, then press and rub them together to activate the tackiness.
The rubbing motion forces the glue into the fibers and builds a tight connection. Once it’s set in place, you simply leave it to cure—no clamping needed.
This technique works best for smaller panels, trim pieces, or fragile parts that can’t handle traditional clamp pressure. It’s also useful in situations where clamps just can’t reach.
Why Surface Prep Matters
To get a strong rub joint, the mating edges need to be perfectly smooth and flat. Any gaps or inconsistencies weaken the suction and prevent a proper bond from forming.
Jodee demonstrates a technique called “book folding” to ensure a perfect match. This involves clamping the two pieces together like a book, then planing both edges simultaneously. The result is two mirror-image edges that line up exactly.
Flat surfaces also reduce glue squeeze-out and make for cleaner results overall. The quality of your edge prep has the biggest impact on the strength of this technique.
Applying the Right Amount of Glue
With a rub joint, less is more. You don’t want to flood the edge with glue—the goal is a thin, even coat that bonds without sliding around.
Run a narrow bead of glue along one edge and spread it evenly. When you press the other piece in place, apply gentle pressure and rub the surfaces back and forth just enough to build initial tack.
Too much glue can make the pieces slippery, while too little won’t activate the suction effect. It takes a bit of trial and error to get it just right, but the results are worth it.
Choosing the Right Glue
Jodee recommends Titebond II for this technique, and with good reason. It sets quickly, forms a strong bond, and has the right consistency to activate the rub joint’s tackiness.
Some woodworkers have tried hide glue for its natural tack, but Jodee notes that liquid hide glue doesn’t offer the same performance. Traditional hot hide glue may work, but for most projects, Titebond II is a dependable choice.
Experimenting with different adhesives can be educational, but for reliable results, stick with a quality wood glue that’s designed for strong initial tack.
Level Surfaces Make a Difference
To keep the pieces from drifting while the glue sets, it’s important to work on a flat, level surface. This helps maintain alignment and keeps the joint from shifting.
If you find the pieces still want to slide, using a couple of light spring clamps near the joint can help stabilize the setup. You’re not applying pressure—just helping the pieces stay still while the glue cures.
A flat bench or assembly table is ideal, especially for smaller parts or longer panels where movement can throw things off.
Enhancing Traditional Glue-Ups
Even if you’re planning to use clamps, this technique can still help. By rubbing the surfaces together first and letting the glue sit for a few minutes, you create a tacky bond that holds everything in place before the clamps go on.
This is especially helpful for larger glue-ups where things tend to slide under pressure. It also allows for more precise alignment before committing to full clamping pressure.
It’s a handy trick that can improve your workflow and reduce frustration during assembly.
Why the Rub Joint Is Worth Knowing
Here are a few reasons this technique deserves a spot in your shop:
- Limited clamps? No problem—this gets the job done without them.
- Delicate workpieces? Avoid crushing fragile parts with unnecessary force.
- Quick tack-up? Save time with minimal setup and cleanup.
- Tight spots? Reach areas where clamps physically can’t fit.
- Precise alignment? Rub joints self-center during the process.
It’s not a replacement for every glue-up, but it’s a powerful option when conditions call for a lighter touch.
Tips for Best Results
- Spend time prepping your edges. A flawless joint starts with perfect surfaces.
- Use a minimal amount of glue and spread it evenly.
- Don’t rush. Allow the glue to become tacky for a few seconds as you rub.
- Use a level surface and light stabilization if needed.
- Choose a glue with good initial tack, like Titebond II.
A Simple Yet Effective Technique
The rub joint is an example of how sometimes, less really is more. By focusing on surface quality and technique, you can get a strong, clean bond with no clamps, no squeeze-out mess, and minimal effort.
Jodee’s demonstration shows how this method can be applied with confidence. Whether you’re working on trim, small panels, or intricate assemblies, the rub joint is a great option to have in your woodworking toolkit.
Support Jodee by visiting his online store here: https://inspirewoodcraft.com/collections/all.