This tip was shared by Jodee from Inspire Woodcraft. It reveals a lesser-known way to use digital calipers—one that improves accuracy and stability when measuring step heights in woodworking projects.
While most woodworkers are familiar with the three standard caliper functions, the fourth method—using the step gauge on the backside—is often overlooked. It’s a simple shift in technique that can make a big difference in precision and ease of use.
Watch the full video and subscribe to Jodee’s channel:
The Three Standard Functions of Digital Calipers
Digital calipers are one of the most versatile measuring tools in any woodworking shop. They’re typically used in three main ways:
- Outside Measurements – The large jaws measure the external dimensions of a board, pipe, or part.
- Inside Measurements – The smaller top jaws check the diameter of holes, slots, or grooves.
- Depth Measurements – A thin rod extends from the bottom of the caliper to measure recesses, mortises, or drilled holes.
These modes cover most measuring needs. But when it comes to measuring vertical steps or height differences—like those found in rabbets or dados—the depth rod can be a bit tricky.
The Step Gauge: A Built-In Feature You Might Be Missing
Flip your calipers over and take a look at the back. You’ll notice a flat metal ledge that moves with the jaws. That’s the step gauge, and it’s designed to measure the vertical offset between two surfaces—what’s known as a step measurement.
Many calipers include this feature, but it’s rarely mentioned in instructions or tutorials. Jodee shows that using the step gauge is often more accurate and far more stable than trying to balance the tool vertically using the depth rod.
How to Use the Step Gauge
Using the step gauge is simple:
- Turn the calipers over so the back side is facing up.
- Open the jaws wide enough to span the step you want to measure.
- Press the fixed jaw firmly against the lower surface.
- Slide the moving jaw down until it contacts the upper surface.
- Read the measurement on the digital display.
This gives you the height difference between the two surfaces. Because the jaws rest flat and wide across the material, the reading is much more stable and reliable.
Why This Method Is More Effective
Many woodworkers default to the depth rod for vertical measurements. But it’s easy to tip, especially when working on shallow cuts or in awkward corners. The step gauge eliminates that issue by providing more surface contact.
Here’s why the step gauge is a better option in many cases:
- More Stability – The wider base means the caliper sits flat instead of teetering like it can with the depth rod.
- Greater Accuracy – Consistent contact with both surfaces reduces the chance of misreadings.
- Easier Handling – No awkward balancing or extra hand pressure needed—just press and measure.
Where It Helps in the Woodshop
Jodee points out a few common woodworking scenarios where the step gauge shines:
- Checking Dado Depths – When routing dados for shelves or dividers, the step gauge gives a faster, more secure reading than a depth rod.
- Measuring Rabbet Shoulders – Accurate shoulder depth is key for a clean rabbet joint, and this method makes it easier to measure the offset.
- Verifying Step Joints – When mating stepped surfaces like in drawer construction, getting the offset right ensures a perfect fit.
These situations come up often, and using the step gauge helps avoid mistakes that could throw off alignment or cause gaps.
Tips for Getting the Most from Your Calipers
Whether you’re using the standard jaws, depth rod, or step gauge, a few small habits can keep your measurements accurate:
- Wipe the Calipers Clean – Dust, chips, and grime can throw off readings. Keep them clean and free of debris.
- Zero Before Measuring – Always reset the caliper to zero before use to ensure accuracy.
- Check for Square Contact – Make sure the jaws are sitting flat and square on your workpiece before reading the display.
- Use the Step Gauge for Tricky Spots – If a depth feels awkward to measure, flip the calipers and try the step gauge instead.
Why This Tip Matters
What makes Jodee’s advice so valuable is that it’s practical, easy to apply, and not widely known. It’s the kind of insight that comes from years in the shop—learning not just how tools work, but how they can work better.
This fourth way to measure with digital calipers is a small adjustment that delivers better results. Once you start using it, you’ll wonder why it’s not more commonly mentioned in caliper tutorials or manuals.
Support Jodee by visiting his online store here: https://inspirewoodcraft.com/collections/all.